DEVICES YOU NEED TO INSTALL A NEW BATH TUB

Devices You Need to Install a New Bath Tub

Devices You Need to Install a New Bath Tub

Blog Article

Go Deal Now

Just how do you feel in regards to How to Install a Bathtub?


Tools You Need to Install a New Bathtub
Installing a tub isn't exactly rocket science, yet it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bathtub with a new one is additionally a moderately tough project. If the old tub is conveniently accessible, the job can relocate speedily; if you have to open up a wall to eliminate the old bathtub and also place the brand-new bathtub, the task is a lot harder. In either case, the job is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the job and also are comfortable trying it. Rather than hiring a specialist to take over a halfway-completed task, it is far better to consider utilizing one prior to you begin. Chances are you might need a professional plumber to make tube links.
This post will certainly assist you set up a brand-new bath tub in your bathroom if you have already purchased a new bathtub and also do not require to change the arrangement of your previous supply of water pipes.
Your devices as well as product list need to consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Removing Old Taps


    If you need to replace old taps with new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, activate the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the restricted gain access to that is typically the situation.
    Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipes have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from transforming throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing compound.
    Prior to going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will certainly require a plastic adapter to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
    If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next off, position the faucet in the installing hole in the bath/basin making certain that the washing machines are in area between the faucet as well as the sink. Secure the faucet in place with the manufacturer supplied backnut. Once the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap connectors. The previous type must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

    Mounting the Bathtub


    Making use of the two wood boards under its feet, place the tub in the required setting. The wooden boards are valuable in evenly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four little points.
    The next objective is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level as well as readjusting the feet on the bathtub up until the level reads degree.
    To install faucets, fit the bottom of the furthest versatile tap port to the proper supply pipe by making a compression sign up with; then do the exact same for the various other tap.
    Switch on the water system and examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet as well as the typical outlet for leaks.
    Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the bath tub should wait up until the bath tub has been utilized a minimum of when as this will settle it right into its last position.

    Getting ready for the Installment


    Firstly, the supporting framework provided with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the taps system to avoid stress on the tub.
    Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of every one of the provided washers.
    Link the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final placement.

    Tiling Around the Bath tub


    In the location where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack an inflexible seal, creating the water to permeate the wall in between the bathroom as well as the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling below.
    You can choose from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water prior to securing, to enable the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not think about this motion before securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or water-proof sticky and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I came across that piece about Tools You Need to Install a New Bathtub when doing a lookup on the search engines. Sharing is good. Helping people is fun. We thank you for reading our article about Installing A Bathtub.




    Make An Appointment


    Report this page